Listings by Brand

Listings by Category

E2S L101 AlertAlight L.E.D. or Filament Bulb Beacon

General Introduction

• High intensity L.E.D.: 8 L.E.D. array @ 2Hz
• Filament Bulb: 3 watt @ 1.5Hz
• Steady or blinking mode
• 7 lens colours available -
  Amber, Blue, Clear, Green, Opal, Red, Yellow
• Remote switching from steady to blinking mode via input terminals on both versions
• Voltages: 12vdc; 24vdc; 48vdc; 24vac; 115vac; 230vac
• Other voltages available upon request
• Mounting via internal BESA compatible fixing positions
• Back box with mounting lugs also available
• IP55 - can be increased to IP56 (dust protected, watertight) with WR kit
• Tropicalisation available on request
• Base enclosure material: UL94V0 & 5VA rated FR ABS
• Base colour available: Red (RAL3000), Grey or White
• Lens Material: Polycarbonate
• Operating temperature: -25 to +55°C
• Storage temperature: -40 to +70°C
• Relative humidity: 90% at 20°C
• Weight 0.20Kg
• Terminals accept 0.5 to 2.5mm² cables

>>> back to e2s menu

E2S L101L-IS Intrinsically Safe EEx ia IIC L.E.D. Warning Beacon

General Introduction
The L101L-IS unit is an intrinsically safe field mounting beacon which provides a bright flashing warning signal in a hazardous area.

The unit can be used independently or combined with an A105N-IS sounder.

When the beacon is used in conjunction with an A105N-IS sounder the alarm accept function can be utilised. By closing a pair of external contacts (i.e push switch) the operator may silence the sounder for between 1 to 30 minutes. If after the preset time the alarm condition still exists the sounder will activate again.

• L101L-IS-C: EEx ia IIC T4 (Tamb. +60°C) Zone 0,1 & 2
• Output frequency:
  Alone: 2Hz (2 double flashes per second)
  With A105N-IS sounder:
  On: 1Hz (1 double flash per second)
  Silenced: 2Hz (2 double flashes per second)
  (alarm accepted)
  Sounder output reduced by typically 2 dB when beacon is activated
• Voltage: 10-28vdc via Zener barrier or galvanic isolator
• ABS flame retardent UL94V0 housing - Red RAL3000
• Sealed to IP56
• LED colours: Amber, Red & Green
• Operating temperature: -40 to +60°C
  Storage temperature: -40 to +70°C
  Relative humidity: 95% at 40°C
• Weight: 0.40Kg
• ITS Certified
  Standard: EN50020: 1994
• Certificate numbers:
  ITS02ATEX2006
  Ex02E2007 IIC system
  Ex02E2008 IIC system
  Ex02E2011 IIB system
  Ex02E2012 IIB system
• Installation:
  The unit may be powered from any certified Zener barrier whose output parameters do not exceed:
  Uo: 28VDC
  lo: 110mA
  Po: 0.8W
  or from any galvanic isolator specified by the system certificates
• Terminals accept 0.5 to 1.5mm² cables
• Current when powered from 24v supply via 28v 300 Ohm Zener barrier
  Alone: 25mA typical
  With A105N-IS sounder: 48mA typical

>>> back to e2s menu

E2S L101 AlertAlight Xenon Strobe Beacon

General Introduction

• 5 Joule @ 1Hz
• 150 Candela output (clear lens)
• Optional 2.5 Joule @ 2 Hz
• 7 lens colours available -
  Amber, Blue, Clear, Green, Opal, Red, Yellow
• Tube life: 5 Million flashes (after which emissions reduced to 70%)
• Voltages: 12vdc; 24vdc; 48vdc; 12vac; 24vac; 48vac; 115vac; 230vac
• Other voltages available upon request
• DC versions have reverse polarity protection
• Mounting via internal BESA compatible fixing positions
• Back box with mounting lugs also available
• IP55 - can be increased to IP56 (dust protected, watertight) with WR kit
• Tropicalisation available on request
• Base colour available: Red (RAL3000), Grey or White
• Lens material: Polycarbonate
• Operating temperature: -25 to +55°C
• Storage temperature: -40 to +70°C
• Relative humidity: 90% at 20°C
• Weight: 0.20Kg
• Terminals accept 0.5 to 4.0mm² cables
• UL approved version available

>>> back to e2s menu

E2S L101 Synchronised AlertAlight Xenon Strobe Beacon

General Introduction

• 5 Joule @ 1Hz
• 150 Candela output (clear lens)
• Full synchronisation on multi-beacon installations
• Alternate flash, FLIP-FLOP selectable mode
• 7 lens colours available -
  Amber, Blue, Clear, Green, Opal, Red, Yellow
• Tube life: 5 Million flashes (after which emissions reduced to 70%)
• Voltages: 12vdc; 24vdc; 48vdc; 12vac; 24vac; 48vac; 115vac; 230vac
• Other voltages available upon request
• DC versions have reverse polarity protection
• Mounting via internal BESA compatible fixing positions
• Back box with mounting lugs also available
• IP55 - can be increased to IP56 (dust protected, watertight) with WR kit
• Tropicalisation available on request
• Base enclosure material: UL94V0 & 5VA rated FR ABS
• Base colour available: Red (RAL3000), Grey or White
• Lens material: Polycarbonate
• Operating temperature: -25 to +55°C
• Storage temperature: -40 to +70°C
• Relative humidity: 90% at 20°C
• Weight: 0.20Kg
• Terminals accept 0.5 to 4.0mm² cables

>>> back to e2s menu

E2S BExCBG05-05D ATEX EEx Hazardous Area Dual Xenon Beacons

General Introduction

• Dual 5 Joule Xenon: 1Hz (60 FPM) (5 Ws)
• BExCBG05-05D: EEx d IIB T5 (Tamb. -50 to +55°C)
• KEMA certified - ATEX/CENELEC approved
• Suitable for Zone 1, 2, 21 & 22, Gas Groups IIB & IIA
• Voltages: 12vdc; 24vdc; 48vdc; 115vac; 230vac
• Other voltages available upon request
• Six lens colours available: Amber, Blue, Clear, Green, Red & Yellow
• Automatic synchronisation on multi-beacon systems
• Beacons can be set to 'flip-flop' alternating mode with other units on multi-beacon systems
• Tube life: emissions reduced to 70% after 8 million flashes
• Xenon tubes mechanically secured against shock/vibration
• BExCBG05-05D: IP67
• Enclosure material: Marine grade LM6 Aluminium
• Chromated & powder coated finish - good resistance to humidity and salt spray environments
• Glass lens & Stainless Steel guard
• Colour available: Red (RAL3000)
• Operating temperature: -50 to +50°C
• Storage temperature: -50 to +70°C
• Large range of certified end of line resistors
• Weight: DC:4.00Kg AC:4.35Kg
• KEMA Certificate number: 01ATEX2222

Installation Features

• Very large termination area
• Dual M20 ISO cable gland entries (supplied with one stopping plug)
• Ratchet adjustable stainless steel 'U' bracket for positive adjustment under harsh conditions
• IN & OUT terminals
• Terminals accept 0.5 to 4.0mm² cables
• Line monitoring: Min. 500 Ohm 2w, or 3k3 Ohm 0.5w resistor, or diode within EExd enclosure (dc versions)
• The beacons may be connected from a single supply for simultaneous operation or from seperate supplies for independent operation.

>>> back to e2s menu

E2S BExBG05D & E ATEX EEx 5 Joule Hazardous Area Xenon Warning Beacons

General Introduction

• 5 Joule Xenon: 1Hz (60 FPM) (5 Ws)
• BExBG05D:
  EEx d IIC T5 (Tamb. -50 to +55°C)
  EEx d IIC T6 (Tamb. -50 to +40°C)
• BExBG05E:
  EEx de IIC T5 (Tamb. -50 to +55°C)
  EEx de IIC T6 (Tamb. -50 to +40°C)
• KEMA certified - ATEX/CENELEC/FTZU approved
• Suitable for Zone 1, 2, 21 & 22, Gas Groups IIC IIB & IIA
• Voltages: 12vdc; 24vdc; 48vdc; 115vac; 230vac
• Six lens colours available: Amber, Blue, Clear, Green, Red & Yellow
• Automatic synchronisation on multi-beacon systems
• Beacons can be set to 'flip-flop' alternating mode with other units on multi-beacon systems
• Tube life: emissions reduced to 70% after 8 million flashes
• Xenon tubes mechanically secured against shock/vibration
• BExCBG05D: IP67 BExBG05E: IP66
• Enclosure material: Marine grade LM6 Aluminium
• Chromated & powder coated finish - good resistance to humidity and salt spray environments
• Glass lens & Stainless Steel guard
• Colour available: Red (RAL3000)
• Operating temperature:
  -50 to +55°C
  -50 to +40°C
• Storage temperature: -50 to +70°C
• Large range of certified end of line resistors
• Weight: DC:2.45Kg AC:2.75Kg
• KEMA Certificate number: 00ATEX2006 X

Installation Features

• Very large termination area
• Dual M20 ISO cable gland entries (supplied with one stopping plug)
• Ratchet adjustable stainless steel 'U' bracket for positive adjustment under harsh conditions
• IN & OUT terminals
• Terminals accept 0.5 to 4.0mm² cables
• Line monitoring: Min. 500 Ohm 2w, or 3k3 Ohm 0.5w resistor, or diode within EExd enclosure (dc versions)

>>> back to e2s menu

E2S BExBG10D & E ATEX EEx 10 Joule Hazardous Area Xenon Warning Beacons

General Introduction

• 10 Joule Xenon: 1Hz (60 FPM) (10 Ws)
• BExBG10D:
  EEx d IIC T4 (Tamb. -50 to +55°C)
  EEx d IIC T5 (Tamb. -50 to +40°C)
• BExBG10E:
  EEx de IIC T4 (Tamb. -50 to +55°C)
  EEx de IIC T5 (Tamb. -50 to +40°C)
• KEMA certified - ATEX/CENELEC/FTZU approved
• Suitable for Zone 1, 2, 21 & 22, Gas Groups IIC IIB & IIA
• Voltages: 12vdc; 24vdc; 48vdc; 115vac; 230vac
• Six lens colours available: Amber, Blue, Clear, Green, Red & Yellow
• Automatic synchronisation on multi-beacon systems
• Beacons can be set to 'flip-flop' alternating mode with other units on multi-beacon systems
• Tube life: emissions reduced to 70% after 8 million flashes
• Xenon tubes mechanically secured against shock/vibration
• BExCBG10D: IP67 BExBG10E: IP66
• Enclosure material: Marine grade LM6 Aluminium
• Chromated & powder coated finish - good resistance to humidity and salt spray environments
• Glass lens & Stainless Steel guard
• Colour available: Red (RAL3000)
• Operating temperature:
  -50 to +55°C (EExd IIC T4)
  -50 to +40°C (EExd IIC T5)
• Storage temperature: -50 to +70°C
• Large range of certified end of line resistors
• Weight: DC:2.45Kg AC:2.75Kg
• KEMA Certificate number: 00ATEX2006 X

Installation Features

• Very large termination area
• Dual M20 ISO cable gland entries (supplied with one stopping plug)
• Ratchet adjustable stainless steel 'U' bracket for positive adjustment under harsh conditions
• IN & OUT terminals
• Terminals accept 0.5 to 4.0mm² cables
• Line monitoring: Min. 500 Ohm 2w, or 3k3 Ohm 0.5w resistor, or diode within EExd enclosure (dc versions)

>>> back to e2s menu

E2S BExBG15D & E ATEX EEx 15 Joule Hazardous Area Xenon Warning Beacons

General Introduction

• 15 Joule Xenon: 1Hz (60 FPM) (15 Ws)
• BExBG15D:
  EEx d IIC T4 (Tamb. -50 to +55°C)
  EEx d IIC T5 (Tamb. -50 to +40°C)
• BExBG10E:
  EEx de IIC T4 (Tamb. -50 to +55°C)
  EEx de IIC T5 (Tamb. -50 to +40°C)
• KEMA certified - ATEX/CENELEC/FTZU approved
• Suitable for Zone 1, 2, 21 & 22, Gas Groups IIC IIB & IIA
• Voltages: 24vdc; 48vdc; 115vac; 230vac
• Six lens colours available: Amber, Blue, Clear, Green, Red & Yellow
• Automatic synchronisation on multi-beacon systems
• Beacons can be set to 'flip-flop' alternating mode with other units on multi-beacon systems
• Tube life: emissions reduced to 70% after 8 million flashes
• Xenon tubes mechanically secured against shock/vibration
• BExCBG15D: IP67 BExBG15E: IP66
• Enclosure material: Marine grade LM6 Aluminium
• Chromated & powder coated finish - good resistance to humidity and salt spray environments
• Glass lens & Stainless Steel guard
• Colour available: Red (RAL3000)
• Operating temperature:
  -50 to +55°C (EExd IIC T4)
  -50 to +40°C (EExd IIC T5)
• Storage temperature: -50 to +70°C
• Large range of certified end of line resistors
• Weight: DC:2.45Kg AC:2.75Kg
• KEMA Certificate number: 00ATEX2006 X

Installation Features

• Very large termination area
• Dual M20 ISO cable gland entries (supplied with one stopping plug)
• Ratchet adjustable stainless steel 'U' bracket for positive adjustment under harsh conditions
• IN & OUT terminals
• Terminals accept 0.5 to 4.0mm² cables
• Line monitoring: Min. 500 Ohm 2w, or 3k3 Ohm 0.5w resistor, or diode within EExd enclosure (dc versions)
• The beacons may be connected from a single supply for simultaneous operation or from seperate supplies for independent operation.

>>> back to e2s menu

E2S BExTBG05D EEx ATEX 5 Joule Telephone Initiated Xenon Warning Beacons

General Introduction

• 5 Joule Xenon: 1Hz (60 FPM) (5 Ws)
• BExTBG05D:
  EEx d IIC T5 (Tamb. -50 to +55°C)
  EEx d IIC T6 (Tamb. -50 to +40°C)
• KEMA certified - ATEX/CENELEC/FTZU approved
• Suitable for Zone 1, 2, 21 & 22, Gas Groups IIC IIB & IIA
• Voltages: 115vac; 230vac
• Six lens colours available: Amber, Blue, Clear, Green, Red & Yellow
• Tube life: emissions reduced to 70% after 8 million flashes
• Xenon tubes mechanically secured against shock/vibration
• BExTBG05D: IP67
• Enclosure material: Marine grade LM6 Aluminium
• Chromated & powder coated finish - good resistance to humidity and salt spray environments
• Glass lens & Stainless Steel guard
• Colour available: Red (RAL3000)
• Operating temperature:
  -50 to +55°C
  -50 to +40°C
• Storage temperature: -50 to +70°C
• Weight: 2.45Kg
• KEMA Certificate number: 00ATEX2006 X
• The ring tone detect circuit senses the ringing voltage on the telephone line and switches the supply onto signal until the telephone is answered

Installation Features

• Very large termination area
• Dual M20 ISO cable gland entries (supplied with one stopping plug)
• Ratchet adjustable stainless steel 'U' bracket for positive adjustment under harsh conditions
• IN & OUT terminals
• Terminals accept 0.5 to 4.0mm² cables
• Telephone line ringing voltage switches power (115vac or 230vac) to enable beacon to operate

>>> back to e2s menu

E2S MB005 & MB010 Marine IP67 5 & 10 Joule Xenon Strobe Beacons

General Introduction
A heavy duty high output IP67 sealed beacon, ideal for harsh environments.

• MB005: 5 Joule @ 1Hz (5 Ws)
• MB010: 10 Joule @ 1Hz (10 Ws)
• Voltages: 12vdc; 24vdc; 48vdc; 24vac; 115vac; 230vac
• Other voltages available upon request
• Six lens colours available
• Automatic synchronised flash, or Flip-Flop alternating mode
• Xenon tube mechanically secured against vibration/shock
• Tube life: emissions reduced to 70% after 8 million flashes
• Reverse polarity protection on DC units
• Third party tested to IP67 & IP66
• Enclosure material: UL94V0 & 5VA rated FR ABS
• Colour available: Grey (RAL7038)
• Operating temperature: -25 to +55°C
• Storage temperature: -40 to +70°C
• Relative humidity: 90% at 20°C
• Weight: 1.48Kg
• Large termination area
• 2 x M20 ISO cable gland entries (with 1 blanking plug)
• Ratchet adjustable stainless steel 'U' bracket for 360° positioning
• All units offer IN & OUT terminals
• Terminals accept 0.5 to 4.0mm² cables

>>> back to e2s menu

E2S MCB005-05 Marine IP67 Dual 5 Joule Xenon Strobe Beacon

General Introduction
A heavy duty high output IP67 sealed beacon, ideal for harsh environments.

• 2 x 5 Joule @ 1Hz beacons (5Ws)
• Voltages: 12vdc; 24vdc; 48vdc; 24vac; 115vac; 230vac
• Other voltages available upon request
• Six lens colours available
• Automatic synchronised flash, or Flip-Flop alternating mode
• Xenon tube mechanically secured against vibration/shock
• Reverse polarity protection on DC units
• Third party tested to IP67 & IP66
• Enclosure material: UL94V0 & 5VA rated FR ABS
• Colour available: Grey (RAL7038)
• Operating temperature: -25 to +55°C
• Storage temperature: -40 to +70°C
• Relative humidity: 90% at 20°C
• Weight: 2.00Kg
• Large termination area
• 2 x M20 ISO cable gland entries (with 1 blanking plug)
• Ratchet adjustable stainless steel 'U' bracket for 360° positioning
• All units offer IN & OUT terminals
• Terminals accept 0.5 to 4.0mm² cables
• Beacons may use the same supply for simultaneous or seperate supplies for independent operation

>>> back to e2s menu